I have discovered some things in the past few months that have allowed me to increase my enjoyment in using my E-Cigarettes.
Some people have noted that they are not getting a very good ‘throat hit’ or significant vapor from theirs. This can be obtained by adjusting the way that you draw from yours. For a satisfying draw you need to slow and extend your draw. A fast draw as on an analog cigarette does not work well on these. Draw into your mouth slowly for 3 to 5 seconds THEN inhale into your lungs. I guarantee that you will notice the difference.
The following series of tips will help with your experience and ease of use of the eGo series of tank cartridge fed vaporizers (e-cigarettes).
I have seen many comments on forums where users complain of their eGo-C’s and eGo-T’s leaking. I believe that these leaks are nothing more than the buildup of condensation in the atomizer cone (the housing that the tank cartridge is inserted into).
When I remove the tank to swap in a new one or to refill the tank, I use a folded strip of paper towel to swab out the bottom of the chamber. Below is a picture of the strip (with a matchbook from NW Sausages to give a sense of scale).
Cut or tear a 1 inch strip from a folded paper towel. I used a towel from a roll that has half-width perforations but a full width piece works just fine.
Fold the strip in thirds lengthwise and then crease one end. Crease full length to be able to use both ends when cleaning two eGo cones.
Insert the strip into the atomizer cone between the center spike and the sidewall. Blot up the condensation by dabbing up and down while rotating the cone with your fingers.
Next, stuff half of the strip into the cone and rotate the cone with your fingers. This will wipe the sidewalls free of condensation.
A shot of the condensation and a bit of coloring on the end of the swab strip.
The use of a cotton swab to do the same thing as the strip. I’ve yet to find a cotton swab that is as absorbent as paper towels but I’ll use them when I’m on the road and can’t find towels.
Be sure to swab the contacts on the bottom of the atomizer as well as the battery contact. I prefer to use a cotton swab for this. Failure to keep these contacts clean can cause a reduction of current resulting in reduced performance of the atomizer. It can also cause blackened deposits to form due to the heating of e-juice between the contacts. I swab mine each time I unscrew the cone from the battery prior to charging.
Another tip that will eliminate possible e-juice leaks is to use silicone caps instead of the standard plastic caps that come with the tanks. These caps have a plug that extends into the tank body which ensures a better seal between cap and tank. The exposed face of the silicone cap seats positively against the face of the atomizer. The silicone material on the face also provides a much better seal around the atomizer spike that pierces the cap and feeds the liquid to the atomizer. The caps are available where you purchase your tanks (esmokeronline) and are included already installed on the tanks available from Mad Vapes.
A silicone tank cap shown installed on an eGo tank (style A – 1ml, the most common size).
An accessory tank that I am fond of is known as a DCT, Dual Coil Tank. The silver tube within the clear polycarbonate tank contains two atomizer coils and wicking material surrounding the air tube in the center. The silver tube is called a cartomizer, carto for short, because it combines an atomizer in the outer cartridge casing.The wicking material is continuously replenished through a hole in the side of the carto. This model holds 3.5ml of juice and provides a little bit different flavor and vapor than does the eGo tank. It also requires less frequent filling.
When using eGo batteries, which provide a nominal 3.4 volts, you should order the 1.5 ohm model. Order 1.5 – 1.7 ohm carto’s to replace the original carto. I find that I need to replace the carto about every 10 days. Your replacement frequency will vary proportionally to how much you use it daily. I estimate a useful lifespan of 12 – 14ml of juice, or approximately 3 – 4 tank refills. You will know it is time to replace it when you notice that the vapor production has fallen off compared to when it is new. I allow it to go for a while as I’m a cheap bastard and it’s a blast when I hit on a new carto and feel the awesome throat hit of a fresh set of coils. At ~$2.50 each, you’ll spend about the same amount per month as you did on a single pack of cigarettes.
The picture below shows the preferred refilling method. Simply remove the tip that extends from the top of the carto and gently push up on the tank by the bottom plug until the carto tube is just below the bottom of the top plug. Place the nozzle of your juice bottle against the inside of the top plug and gently squeeze the bottle until the liquid is right below the top of the carto tube. Next, press the tank back down being sure to center the carto so as not to damage the o-ring inside the top cap. At this point I reccomend dripping 15 – 20 drops of juice into the wicking material in the carto tube. DO NOT drip the liquid directly into the center of the carto tube! Instead, hold the tube at a 45 degree angle and drip the liquid on the side of the inside of the tube allowing it to run down to the wicking material. Drip 1 – 2 drops and rotate the tube a third of a turn before dripping more. Allow it to absorb a bit before dropping more. Once the wicking is wet it will absorb the liquid more readily. If you happen to get liquid down the center tube, all is not lost. Grab a paper towel and blow through the tube until no more liquid comes out the bottom. I suggest cupping the paper towel around the bottom to catch the liquid that will come out of the side vents just above the threaded portion at the bottom of the carto. Once the carto has been primed, reinstall the mouthpiece (tip) and draw rather hard to draw liquid into the wicking. Look at the feedhole through the tank and you will see a bubble or bubbles emerge from the tiny feedhole. Once no more bubbles emerge, the carto is primed. Allow the tank to sit for 10 – 15 minutes so the liquid is evenly distributed throughout the wicking.
Preferred filling position for a dual coil tank.
A top view of a carto (cartridge atomizer). The white material is the wicking. You can see the air tube at the center. The black wire is the wire leading to the top heating coil. The wires to the lower coil and to the center of the coils are buried in the wicking. The mouthpiece is inserted in the top of this tube.
The left vaporizer is an eGo-C cone on an eGo style 650mAh battery. The middle unit is a 3.5ml DCT on an eGo style 1100mAh battery. The unit on the right is a DCT on an eGo style 900mAh pass-through battery. A pass-through has a USB port on the bottom to facilitate charging as well as usage without battery depletion when plugged into a USB port on your computer or wall mount power supply.
An eGo style 900mAh pass-through battery plugged into the USB port of my laptop. Anne calls this my Robot Cigarette…
If you choose to shop at Northwest Vapors (I love them!) be sure to use the redemption code FOXFUR and receive a 10% discount on your entire order. You can use this on your first and every order after that. I told them I blog about E-Cigs (it is the most frequently accessed topic on this blog) and would like to be able to offer my readers a discount. They immediately created the Foxfur code. I am not paid or compensated by them for traffic directed over there. I simply want y’all to save some money and your health.